• Inputs and Outputs |
Digital Inputs |
4 channels |
Configurable DIOs (by jumper) |
4 channels |
Analog Inputs |
4 channels |
Isolation |
3k VDC or 2k Vrms |
• Digital Input |
Sensor Type |
Wet Contact (NPN or PNP), Dry Contact |
I/O Mode |
DI or Event Counter |
Dry Contact |
• On: short to GND
• Off: open |
Wet Contact (DI to COM) |
• On: 10 to 30 VDC
• Off: 0 to 3 VDC |
Common Type |
4 points per COM |
Counter Frequency |
250 Hz |
Digital Filtering Time Interval |
Software Configurable |
• Digital Output |
Type |
Sink |
I/O Mode |
DO or Pulse Output |
Pulse Output Frequency |
500 Hz |
Over-Voltage Protection |
45 VDC |
Over-Current Protection |
2.6 A (4 channels @ 650 mA) |
Over-Temperature Shutdown |
175°C (typical), 150°C (min.) |
Current Rating |
200 mA per channel |
• Analog Input |
Type |
Differential input |
Resolution |
16 bits |
I/O Mode |
Voltage / Current (jumper selectable) |
Input Range |
0 to 10 VDC, 0 to 20 mA, 4 to 20 mA, 4 to 20 mA (burnout detection) |
Accuracy |
±0.1% FSR @ 25°C
±0.3% FSR @ -10 and 60°C
±0.5% FSR @ -40 and 75°C |
Sampling Rate |
• All channels: 12 samples/sec
• Per channel: 3 samples/sec
• Only one channel enabled: 12 samples/sec |
Input Impedance |
10 mega-ohms (min.) |
Built-in Resistor for Current Input |
120 ohms |
• Power Requirements |
Input Voltage |
12 to 36 VDC |
Input Current |
139 mA @ 24 VDC |
• MTBF (mean time between failures) |
Time |
502,210 hrs |
Standard |
Telcordia SR332 |
Common Specifications
|
• LAN |
Ethernet |
2 switched 10/100 Mbps RJ45 ports |
Protection |
1.5 kV magnetic isolation |
Protocols |
Modbus/TCP (Slave), EtherNet/IP*, SNMPv1/v2c, RESTful API, TCP/IP, UDP, DHCP, BOOTP, HTTP |
|
• Physical Characteristics |
Wiring |
I/O cable max. 14 AWG |
Dimensions |
27.8 x 124 x 84 mm (1.09 x 4.88 x 3.31 in) |
Weight |
Under 200 g (0.44 lb) |
Mounting |
DIN rail or wall |
• Environmental Limits |
Operating Temperature |
Standard Models: -10 to 60°C (14 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F) |
Storage Temperature |
-40 to 85°C (-40 to 185°F) |
Ambient Relative Humidity |
5 to 95% (non-condensing) |
Shock |
IEC 60068-2-27 |
Vibration |
IEC 60068-2-6 |
Altitude |
Up to 2000 m |
|
|
• Standards and Certifications |
Safety |
UL 508 |
EMC |
EN 55032, EN 55024, EN 61000-3-2/3-3, EN 61000-6-2/6-4 |
EMI |
CISPR 32, FCC Part 15B Class A |
EMS |
IEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 3 V/m
IEC 61000-4-4 EFT: Power: 2 kV; Signal: 1 kV
IEC 61000-4-5 Surge: Power: 2 kV; Signal: 1 kV
IEC 61000-4-6 CS: 10 V
IEC 61000-4-8 |
Hazardous Location |
Class 1 Division 2, ATEX Zone 2 |
Green Product |
RoHS, CRoHS, WEEE |
Note |
Please check Moxa’s website for the most up-to-date certification status. |