ethernet-remote-i-o-with-2-port-ethernet-switch-4-dis-4-dios-4-ais.png

Features and Benefits E1242 IoLogik - Ethernet remote I/O with 2-port Ethernet switch, 4 DIs, 4 DIOs, 4 AIs

  • User-definable Modbus/TCP Slave addressing
  • Supports EtherNet/IP* adapter mode
  • Supports RESTful API for IIOT applications
  • 2-port Ethernet switch for daisy-chain topologies
  • Save time and wiring cost with peer-to-peer communications
  • Active communications with MX-AOPC UA Server
  • Supports SNMPv1/v2c
  • Easy mass deployment and configuration with ioSearch utility
  • Friendly configuration via web browser
  • Simplify I/O management with MXIO library on either a Windows or Linux platform
  • Class I Division 2, ATEX Zone 2 certification
  • Wide operating temperature range: -40 to 75°C (-40 to 167°F) 
    *Requires online registration (available free of charge)

Introduction

I/O to IT/OT Protocol Conversion

The ioLogik E1200 does just what you need by supporting the most often-used protocols for retrieving I/O data. Most IT engineers use SNMP or RESTful API protocols, but IA engineers are more familiar with Operational Technologies (OT), such as Modbus and EtherNet/IP. Moxa's Smart I/O makes it possible for both IT and IA engineers to conveniently retrieve data from the same I/O device. The ioLogik E1200 series speaks six different protocols, including Modbus/TCP, EtherNet/IP, and Moxa AOPC for IA engineers, as well as SNMP, RESTful API, and Moxa MXIO library for IT engineers. The ioLogik E1200 retrieves I/O data and converts the data to any of these protocols at the same time, allowing you to get your applications connected easily and effortlessly. Learn more…


Daisy-chained Ethernet I/O Connection

A new daisy-chained Ethernet I/O concept is now available. The ioLogik E1210 industrial Ethernet remote I/O has two embedded Ethernet switch ports that allow information to flow to another local Ethernet device or connect to the next ioLogik in the daisy-chain.

Applications such as factory automation, security and surveillance systems, and tunnel monitoring, can make use of daisy-chained Ethernet for building multi-drop I/O networks over standard Ethernet cables. Many industrial automation users are familiar with the multi-drop configuration typically used in fieldbus applications. The daisy-chain function on the Ethernet remote   I/O ioLogik E1210 not only increases the connection between machines and panels, but also lowers the cost of buying separate Ethernet switches, and at the same time reduces labor fees and cabling by a large percentage. For example, if a production facility contains 700 stations (20 points per station), the wiring cost reduction can reach 15% of the total implementation cost.

 

Saving Time and Wiring Costs with Peer-to-Peer Communications

In remote automation applications, the control room and sensors are often far removed, making wiring over long distances a constant challenge. With peer-to-peer networking, users may now map a pair of ioLogik E1200 series modules so that input values will be directly transferred to output channels, greatly simplifying the wiring process and reducing wiring costs.

 

 

User-definable Modbus/TCP Addressing for Painless Upgrading of Existing Systems

For Modbus devices that are controlled and detected by fixed addresses, users need to spend a vast amount of time researching and verifying the configurations. Users need to locate each device’s networking details like I/O channels, or vendor-defined addresses to enable the initial or start address of a SCADA system or PLC. The ioLogik E1200, with user-definable Modbus/TCP addressing, offers greater flexibility, and setup is easy. Instead of worrying about individual devices, users simply configure the function and address map to fit their needs.

 ioLogik E1242 Specifications
• Inputs and Outputs
Digital Inputs 4 channels
Configurable DIOs (by jumper) 4 channels
Analog Inputs 4 channels
Isolation 3k VDC or 2k Vrms
• Digital Input
Sensor Type Wet Contact (NPN or PNP), Dry Contact
I/O Mode DI or Event Counter
Dry Contact • On: short to GND
• Off: open
Wet Contact (DI to COM) • On: 10 to 30 VDC 
• Off: 0 to 3 VDC
Common Type 4 points per COM
Counter Frequency 250 Hz
Digital Filtering Time Interval Software Configurable
• Digital Output
Type Sink
I/O Mode DO or Pulse Output
Pulse Output Frequency 500 Hz
Over-Voltage Protection 45 VDC
Over-Current Protection 2.6 A (4 channels @ 650 mA)
Over-Temperature Shutdown 175°C (typical), 150°C (min.)
Current Rating 200 mA per channel
• Analog Input
Type Differential input
Resolution 16 bits
I/O Mode Voltage / Current (jumper selectable)
Input Range 0 to 10 VDC, 0 to 20 mA, 4 to 20 mA, 4 to 20 mA (burnout detection)
Accuracy ±0.1% FSR @ 25°C
±0.3% FSR @ -10 and 60°C
±0.5% FSR @ -40 and 75°C
Sampling Rate • All channels: 12 samples/sec
• Per channel: 3 samples/sec
• Only one channel enabled: 12 samples/sec
Input Impedance 10 mega-ohms (min.)
Built-in Resistor for Current Input 120 ohms
• Power Requirements
Input Voltage 12 to 36 VDC
Input Current 139 mA @ 24 VDC
• MTBF (mean time between failures)
Time 502,210 hrs
Standard Telcordia SR332
• Common Specifications
• LAN
Ethernet 2 switched 10/100 Mbps RJ45 ports
Protection 1.5 kV magnetic isolation
Protocols Modbus/TCP (Slave), EtherNet/IP*, SNMPv1/v2c, RESTful API, TCP/IP, UDP, DHCP, BOOTP, HTTP
*Requires online registration at https://www.moxa.com/Event/DAC/2016/Smart_EIP_IO/index.htm (available free of charge)
• Physical Characteristics
Wiring I/O cable max. 14 AWG
Dimensions 27.8 x 124 x 84 mm (1.09 x 4.88 x 3.31 in)
Weight Under 200 g (0.44 lb)
Mounting DIN rail or wall
• Environmental Limits
Operating Temperature Standard Models: -10 to 60°C (14 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temperature -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity 5 to 95% (non-condensing)
Shock IEC 60068-2-27
Vibration IEC 60068-2-6
Altitude Up to 2000 m
Note Please contact Moxa if you require products guaranteed to function properly at higher altitudes.
• Standards and Certifications
Safety UL 508
EMC EN 55032, EN 55024, EN 61000-3-2/3-3, EN 61000-6-2/6-4
EMI CISPR 32, FCC Part 15B Class A
EMS IEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 3 V/m
IEC 61000-4-4 EFT: Power: 2 kV; Signal: 1 kV
IEC 61000-4-5 Surge: Power: 2 kV; Signal: 1 kV
IEC 61000-4-6 CS: 10 V
IEC 61000-4-8
Hazardous Location Class 1 Division 2, ATEX Zone 2
Green Product RoHS, CRoHS, WEEE
Note Please check Moxa’s website for the most up-to-date certification status.
• Warranty
Warranty Period 5 years
Details See www.moxa.com/warranty
Note Because of the limited lifetime of power relays, products that use this component are covered by a 2-year warranty.